[2022] Pass HP HPE2-T37 Exam Updated 81 Questions [Q18-Q33] : Exams Labs Braindumps : http://blog.examslabs.com

NEW QUESTION 18
As a part of troubleshooting, you have to reinstall the same version of the firmware on an HPE Synergy Compute Module. Click the area within the Firmware section of the server profile that will allow you to install the same firmware version.

NEW QUESTION 19
Which statement about a server profile for an Apollo system is true?

Fibre Channel connections can be defined

UEFI optimized is the only available boot mode

Virtual WWNs and MAC addresses can be defined

Enclosure Group Is automatically selected

NEW QUESTION 20
For HPE Primera, match each task with the management tool that can be used to perform it.

NEW QUESTION 21
You configured downlink aggregation for one of the HPE Synergy Compute Modules in an environment by placing two connections in the same Link Aggregation Group. After you made the changes to the server profile, its status changed to critical.
What can be done to fix this issue?

The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.

The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.

Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.

Ensure that the Link Aggregation Group time-out value matches the server set values.

NEW QUESTION 22
Which statement about access to HPE Onboard Administrator is true when an HPE BladeSystem enclosure is added to HPE OneView?

It is blocked when an HPE BladeSystem enclosure is managed using HPE OneView.

It is enabled only when an HPE BladeSystem enclosure is monitored using HPE OneView.

It is enabled when an HPE BladeSystem is either managed or monitored using HPE OneView.

It is blocked when HPE BladeSystem enclosure is monitored using HPE OneView.

NEW QUESTION 23
Your customer added HPE Primera to HPE OneVlew and enabled volume provisioning on all storage pools. For security reasons, the customer wants to disable volume provisioning using HPE OneView on a specific storage pool.
How can this task be completed?

The storage pool should be removed from HPE OneView using a PowerShell script.

The storage pool should be disabled using the array management tool.

The storage pool state should be changed to discovered using HPE OneView.

The storage pool should be marked as read-only using HPE OneView.

NEW QUESTION 24
Your customer built a sever profile for HPE Synergy Gen 10 server and configured boot mode to Legacy BIOS. Which feature Is not available for this Compute Module?

BIOS management

Workload profile

Boot from SAN

Secure boot

NEW QUESTION 25
You are creating a Logical Interconnect Group for a three-frame HPE Synergy solution with HPE Virtual Connect SE100Gb F32 Modules for Synergy.
In which scenario should you set redundancy for master modules to be highly available?

When storm control or loop protection will be enabled for Virtual Connect modules

When each of the frames has two Virtual Connect modules installed

When each Virtual Connect module is installed in different frame

When each Virtual Connect module is installed in different fabric

NEW QUESTION 26
Refer to the exhibit.

Which statement about the logical interconnect shown is true?

For FC uplink sets, an additional uplink from second module should be added for redundancy.

The maximum supported number of the internal networks for logical interconnect is configured.

Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.

FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.

NEW QUESTION 27
Which types of support dump can be created using HPE OneView? (Select two.)

Enclosure group support dump

Appliance support dump

Firmware deployment support dump

Logical enclosure support dump

Maintenance console support dump

NEW QUESTION 28
Refer to the exhibit.

Which statement about server connections is true?

LACP on downlinks is configured for Ethernet connection

All connections within the server profile are using physical IDs

Ethernet connection is configured to boot from PXE

Storage array is connected directly to an HPE Synergy frame

NEW QUESTION 29
Your customer asks you if it is possible to perform HPE Synergy initial setup remotely. How should you respond?

Remote HPE Synergy setup is possible if HPE Composer 2 is used and a DHCP server Is available in the management network.

Remote HPE Synergy Installation can be done only if an additional set of the services was purchased together with hardware platform.

HPE Synergy cannot be deployed remotely, as Initial setup must be performed using a local console connection.

HPE Synergy can be configured remotely through a secure connection to the FLM if this option was enabled In the factory.

NEW QUESTION 30
You want to add the latest IL0 firmware to an HPE OneView firmware repository. How can you complete this task?

A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.

A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.

An external repository must be created, because standalone components are supported only In an external repository.

ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.

NEW QUESTION 31
Click option that will allow you to select a FlexNIC function for the specified connection.

NEW QUESTION 32
Which statement about a Logical Enclosure for HPE BladeSystem is Hue?

A logical enclosure can have between 1 to 5 HPE BladeSystem c7000 enclosures.

A logical enclosure must be created only for monitored HPE BladeSystem C700O enclosures.

A logical enclosure is created automatically, and it is always based on a single enclosure.

A logical enclosure can contain a mix of HPE BladeSystem c7000 and C3000 enclosures.

NEW QUESTION 33
Your customer plans to use HPE OneView to manage a small environment based on HPE ProLiant servers that includes G7 and Gen 10 systems. What should you explain to this customer?

HPE Management Agent must he installed for HPE ProLiant Gen 10 servers.

HPE ProLiant G7 and Gen10 cannot be managed using the same appliance.

Not all of the features will be available for HPE ProLiant G7 systems.

HPE ProLiant Gen 10 servers do not need an HPE OneView license.