This page was exported from Exams Labs Braindumps [ http://blog.examslabs.com ] Export date:Fri Jul 5 20:16:36 2024 / +0000 GMT ___________________________________________________ Title: Pass 300-410 Brain Dump Updated Certification Sample Questions [Q101-Q123] --------------------------------------------------- Pass 300-410 Brain Dump Updated Certification Sample Questions Online 300-410 Test Brain Dump Question and Test Engine Difference Between CCENT and CCNA CCENT is an entry-level certification for aspiring Network engineers. It validates the skills needed to support a small network and also provides basic knowledge of routing and switching fundamentals. CCNA, on the other hand, is suitable for experienced Network Engineers with interest in networking and routing concepts. Comment on the latest changes in Cisco certification details. Sources for review Cisco Technical Certifications CCENT. Marks the completion of the CCENT foundation. Practicing the skills needed to support a small network. Customer Support Engineer, Computer Support Specialist, Network Administrator are some common jobs for CCENT candidates. Mock Test for Preparation of CCNA. Offer the best Cisco 300-410 exam materials.   NEW QUESTION 101Refer to the exhibit. Your company security policy states you must use SSH on your network devices. Your attempt to SSH into SW3 is unsuccessful. What action must you take to correct the issue?  Change access-class 100 in to access-class 175 in.  Change access-class 100 in to access-class 150 in.  Change access-class 100 in to access-class 100 out.  Change transport inut ssh to transport input telnet NEW QUESTION 102Refer to the exhibit.An engineer configured IP SLA on R1 to avoid the ISP link flapping problem. but it is not working as designed IP SLA should wait 30 seconds before switching traffic to a secondary connection and then revert to the primary link after waning 20 seconds, when the primary link is available and stabilized. Which configuration resolves the issue?  R1(config)#ip sla 700R1(config-ip-sla)#delay down 30 up 20  R1(config)#ip sla 700R1(config-ip-sla)#delay down 20 up 30  R1(config)#track 700 ip sla 700R1(config-track)#delay down 30 up 20  R1(config)#track 700 ip sla 700R1(config-track)#delay down 20 up 30 NEW QUESTION 103Refer to the exhibit.After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?  Set the administrative distance 100 under the RIP process on R2.  Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.  Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.  Redistribute the directly connected interfaces on R2. NEW QUESTION 104When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template.”. What is the reason for the error?  The software version of the template is different from the software version of the device  The changes to the template were not committed  The template has an incorrect configuration.  The tag that was used to filter the templates does not match the device tag. NEW QUESTION 105Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?  Change the direction of the distribute-list command from out to in.  Remove the line with the sequence number 5 from the prefix list.  Remove the prefix keyword from the distribute-list command.  Remove the line with the sequence number 10 from the prefix list. NEW QUESTION 106Refer to the exhibit.During troubleshooting it was discovered that the device is not reachable using a secure web browser.What is needed to fix the problem?  permit tcp port 465.  permit tcp port 443  permit udp port 465  permit tcp port 22 NEW QUESTION 107How are MPLS Layer 3 VPN services deployed?  The RD and RT values must match under the VRR  The RD and RT values under a VRF must match on the remote PE router  The import and export RT values under a VRF must always be the same.  The label switch path must be available between the local and remote PE routers. Explanationhttps://www.cisco.com/c/en/us/td/docs/iosxr/ncs5500/vpn/65x/b-l3vpn-cg-ncs5500-65x/b-l3vpn-cg-ncs5500-65xNEW QUESTION 108Refer to the exhibit.An engineer configured NetFlow on R1, but the NMS server cannot see the flow from ethernet 0/0 of R1.Which configuration resolves the issue?  flow monitor Flowmonitor1source Ethernet0/0  interface Ethernet0/1ip flow monitor Flowmonitor1 inputip flow monitor Flowmonitor1 output  interface Ethernet0/0ip flow monitor Flowmonitor1 inputip flow monitor Flowmonitor1 output  flow exporter FlowAnalyzer1source Ethernet0/0 NEW QUESTION 109An engineer configured a company’s multiple area OSPF head office router and Site A cisco routers with VRF lite. Each site router is connected to a PE router of an MPLS backbone.After finishing both site router configurations, none of the LSA 3,4 5, and 7 are installed at Site A router. Which configuration resolves this issue?  configure capability vrf-lite on Site A and its connected PE router under router ospf 1 vrf abc  configure capability vrf-lite on Head Office and its connected PE router under router ospf 1 vrf abc  configure capability vrf-lite on both PE routers connected to Head Office and Site A routers under routtr ospf 1 vrf abc  configure capability vrf-lite on Head Office and Site A routers under router ospf 1 vrf abc NEW QUESTION 110Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?  Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command  Disable IPv6 on the E 0/0 interface using the no ipv6 enable command  Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command  Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface. ExplanationOnce again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the “ospfv3” keyword instead ofthe earlier “ipv6 router ospf” routing process command and “ipv6 ospf” interface commands.The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may havetwo processes per interface, but only one process per address family (AF).NEW QUESTION 111Drag and drop the MPLS VPN device types from me left onto the definitions on the right. NEW QUESTION 112What is a limitation of IPv6 RA Guard?  It is not supported in hardware when TCAM is programmed  It does not offer protection in environments where IPv6 traffic is tunneled.  It cannot be configured on a switch port interface in the ingress direction  Packets that are dropped by IPv6 RA Guard cannot be spanned ExplanationRestrictions for IPv6 RA Guard* The IPv6 RA Guard feature does not offer protection in environments where IPv6 traffic is tunneled.* This feature is supported only in hardware when the ternary content addressable memory (TCAM) is programmed.* This feature can be configured on a switch port interface in the ingress direction.* This feature supports host mode and router mode.* This feature is supported only in the ingress direction; it is not supported in the egress direction.* This feature is not supported on EtherChannel and EtherChannel port members.* This feature is not supported on trunk ports with merge mode.* This feature is supported on auxiliary VLANs and private VLANs (PVLANs). In the case of PVLANs, primary VLAN features are inherited and merged with port features.* Packets dropped by the IPv6 RA Guard feature can be spanned.NEW QUESTION 113An engineer configured SNMP notifications sent to the management server using authentication and encrypting data with DES. An error in the response PDU is received as “UNKNOWNUSERNAME. WRONGDIGEST”. Which action resolves the issue?  Configure the correct authentication password using SNMPv3 authPriv .  Configure the correct authentication password using SNMPv3 authNoPriv.  Configure correct authentication and privacy passwords using SNMPv3 authNoPriv.  Configure correct authentication and privacy passwords using SNMPv3 authPriv. https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/snmp/configuration/15-e/snmp-15-e-book.pdf There are three SNMP security levels (for SNMPv1, SNMPv2c, and SNMPv3):+ noAuthNoPriv: Security level that does not provide authentication or encryption. + authNoPriv: Security level that provides authentication but does not provide encryption. + authPriv: Security level that provides both authentication and encryption.For SNMPv3, “noAuthNoPriv” level uses a username match for authentication.NEW QUESTION 114Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right. ExplanationSame Answer is already updated below:HTTP and HTTPs run on TCP port 80 and 443, respectively and we have to remember them.Syslog runs on UDP port 514 while NTP runs on UDP port 123 so if we remember them we can find out the matching answers easily. But maybe there is some typos in this question as 2001:d88:800:200c::c/126 only ranges from 2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f (4 hosts in total). It does not cover host 2001:0D88:0800:200c::1f. Same for 2001:D88:800:200c::e/126, which also ranges from2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f and does not cover host 2001:0D88:0800:200c::1c.NEW QUESTION 115Drag and drop the packet types from the left onto the correct descriptions on the right. ExplanationUnlike legacy network technologies such as ISDN, Frame Relay, and ATM that defined separate data and control channels, IP carries all packets within a single pipe. Thus, IP network devices such as routers and switches must be able to distinguish between data plane, control plane, and management plane packets to treat each packet appropriately.From an IP traffic plane perspective, packets may be divided into four distinct, logical groups:1. Data plane packets – End-station, user-generated packets that are always forwarded by network devices to other end-station devices. From the perspective of the network device, data plane packets always have a transit destination IP address and can be handled by normal, destination IP address-based forwarding processes.2. Control plane packets – Network device generated or received packets that are used for the creation and operation of the network itself. From the perspective of the network device, control plane packets always have a receive destination IP address and are handled by the CPU in the network device route processor. Examples include protocols such as ARP, BGP, OSPF, and other protocols that glue the network together.3. Management plane packets – Network device generated or received packets, or management station generated or received packets that are used to manage the network. From the perspective of the network device, management plane packets always have a receive destination IP address and are handled by the CPU in the network device route processor. Examples include protocols such as Telnet, Secure Shell (SSH), TFTP, SNMP, FTP, NTP, and other protocols used to manage the device and/or network.4. Services plane packets – A special case of data plane packets, services plane packets are also user-generated packets that are also forwarded by network devices to other end-station devices, but that require high-touch handling by the network device (above and beyond normal, destination IP address-based forwarding) to forward the packet. Examples of high-touch handling include such functions as GRE encapsulation, QoS, MPLS VPNs, and SSL/IPsec encryption/decryption, etc. From the perspective of the network device, services plane packets may have a transit destination IP address, or may have a receive destination IP address (for example, in the case of a VPN tunnel endpoint).NEW QUESTION 116Which statement about route distinguishers in an MPLS network is true?  Route distinguishers allow multiple instances of a routing table to coexist within the edge router.  Route distinguishers are used for label bindings.  Route distinguishers make a unique VPNv4 address across the MPLS network.  Route distinguishers define which prefixes are imported and exported on the edge router. Section: VPN TechnologiesExplanation/Reference:NEW QUESTION 117Which two protocols work in the control plane of P routers across the MPLS cloud? (choose two)  LSP  RSVP  ECMP  LDP  MPLS OAM NEW QUESTION 118Drag and drop the MPLS VPN device types from the left onto the definitions on the right. ExplanationGraphical user interface, application Description automatically generatedNEW QUESTION 119Exhibit:Which action resolves the authentication problem?  Configure the user name on the TACACS+ server  Configure the UDP port 1812 to be allowed on the TACACS+ server  Configure the TCP port 49 to be reachable by the router  Configure the same password between the TACACS+ server and router. ExplanationFrom the last line of the output, we notice that the result was “Invalid AUTHEN packet”. Therefore something went wrong with the username or password.NEW QUESTION 120Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:Interface fastethernet 0/0description Client DHCP ID 394482431Ip address 172 31 11 255 255.255 0!ip route 172.16.1.0 255 255 255.0 10.1.1.2Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?  RouterB(config-if)#lp helper-address 172.31.1.1  RouterBiconfig-ififclp helper-address 255.255 255 255  RouterB(config-if)#lp helper-address 172.16.1.1  RouterB(config-if)#lp helper-address 172.16.1.2 NEW QUESTION 121Refer to the exhibit.What is the result of applying this configuration?  The router can form BGP neighborships with any other device.  The router cannot form BGP neighborships with any other device.  The router cannot form BGP neighborships with any device that is matched by the access list named“BGP”.  The router can form BGP neighborships with any device that is matched by the access list named“BGP”. Explanationafter bgp session are UP.I configured the CoPP to drop 10.3.3.3 bgp traffic (R3).R3 bgp traffic that matched the ACL 100 is dropped and the state is in IDLE——————————————–access-list 100 permit tcp host 10.3.3.3 any eq bgpaccess-list 100 permit tcp host 10.3.3.3 eq bgp any!class-map match-all class-bgpmatch access-group 100!policy-map policy-bgpclass class-bgpdrop!control-planeservice-policy input policy-bgp!The 10.3.3.3 neighbor goes to IDLENEW QUESTION 122Refer to the exhibit.After redistribution is enabled between the routing protocols, PC2, PC3, and PC4 cannot reach PC1.Which action can be engineer take to solve the issue so that all the PCs are reachable?  Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.  Set the administrative distance 100 under the process on R2.  Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.  Redistribute the directly connected interfaces on R2. NEW QUESTION 123What are two functions of MPLS Layer 3 VPNs? (Choose two.)  LDP and BGP can be used for Pseudowire signaling.  It is used for transparent point-to-multipoint connectivity between Ethernet links/sites.  BGP is used for signaling customer VPNv4 routes between PE nodes.  A packet with node segment ID is forwarded along with shortest path to destination.  Customer traffic is encapsulated in a VPN label when it is forwarded in MPLS network. ExplanationMPLS Layer-3 VPNs provide IP connectivity among CE sites* MPLS VPNs enable full-mesh, hub-andspoke, and hybrid IP connectivity* CE sites connect to the MPLS network via IP peering across PE-CE links* MPLS Layer-3 VPNs are implemented via VRFs on PE edge nodes* VRFs providing customer routing and forwarding segmentation* BGP used for signaling customer VPN (VPNv4) routes between PE nodes* To ensure traffic separation, customer traffic is encapsulated in an additional VPN label when forwarded in MPLS network* Key applications are layer-3 business VPN services, enterprise network segmentation, and segmented layer-3 Data Center access Loading … Real Cisco 300-410 Exam Dumps with Correct 335 Questions and Answers: https://www.examslabs.com/Cisco/CCNP-Enterprise/best-300-410-exam-dumps.html --------------------------------------------------- Images: https://blog.examslabs.com/wp-content/plugins/watu/loading.gif https://blog.examslabs.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2022-05-24 05:44:37 Post date GMT: 2022-05-24 05:44:37 Post modified date: 2022-05-24 05:44:37 Post modified date GMT: 2022-05-24 05:44:37