This page was exported from Exams Labs Braindumps [ http://blog.examslabs.com ] Export date:Thu Nov 21 18:25:18 2024 / +0000 GMT ___________________________________________________ Title: Download Latest 300-425 Dumps with Authentic Real Exam QA's [Q66-Q90] --------------------------------------------------- Download Latest 300-425 Dumps with Authentic Real Exam Questions Authentic 300-425 Exam Dumps PDF - Dec-2022 Updated QUESTION 66Refer to the exhibit.An enterprise is using wireless as the main network connectivity for clients. To ensure service continuity, a pair of controllers will be installed in a datacenter An engineer is designing SSO on the pair of controllers What needs to be included m the design to avoid having the secondary controller go into maintenance mode?  The keep alive timer is too low which causes synchronization problems.  The connection between the redundancy ports is missing.  The redundancy port must be the same subnet as the redundancy mgmt.  The Global Configuration of SSO is set to Disabled on the controller. QUESTION 67A wireless engineer is designing a wireless network to support real-time applications over wireless. Which IEEE protocol must the engineer enables on the WLC so that the number of packets that are exchanged between an access point and client are reduced and fast roaming occurs?  802.11w  802.11r  802.11i  802.11k QUESTION 68A customer has noticed that Client Band Select is enabled and no clients are utilizing the 5 GHz band. Which three parameters must be met to ensure that wireless clients use the 5 GHz band? (Choose three.)  Ensure that channel bonding is enabled on the WLAN.  Ensure that the co-channel interference has not exceeded −85 dBm.  Ensure that the UNII-2 extended channels are enabled on the 802.11a radios.  Ensure that the client is receiving RSSI above the minimum band select RSSI threshold.  Ensure that the client is dual-band capable.  Ensure that the WLAN has 802.11a enabled. Section: Wired and Wireless InfrastructureQUESTION 69Why is 802.11a connectivity reduced in an X-ray room?  X-rays create significant non-Wi-Fi interference on the 802.11a band.  X-rays impact the 802,11a UNll-2 channels that cause access points to dynamically change channels.  X -rays within these rooms cause multipath issues.  X-ray rooms exhibit increased signal attenuation. QUESTION 70When conducting a site survey for real-time traffic over wireless, which two design capabilities of smartphones and tablets must be considered? (Choose two.)  no support for 802.11ac  higher data rates than laptops  fewer antennas than laptops  no support for 802.11r  lower data rates than laptops QUESTION 71A network engineer is configuring high availability on an access point. What is the maximum number of controllers that can be configured?  1  2  3  4 ExplanationSo max 2 will be supported on an AP.QUESTION 72Refer to the exhibit.What is the main reason why the Wi-Fi design engineer took a different approach than installing the APs in the offices, even though that installation provides better coverage?  aesthetics  transmit power considerations  antenna gain  power supply considerations https://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob30dg/RFDesign.html#wp1000551QUESTION 73A wireless engineer is designing a wireless network for a warehouse using access points with internal antennas. Which two elements have a negative effect on the wireless users? (Choose two.)  wireless channels  access point height  client authentication  client authorization  absorption https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1250-series/design_guide_c07-693245.html#_Toc309331086QUESTION 74A rapidly expanding company has tasked their network engineer with wirelessly connecting a new cubicle area with Cisco workgroup bridges until the wired network is complete. Each of 42 new users has a computer and VoIP phone. How many APs for workgroup bridging must be ordered to keep cost at a minimum while connecting all devices?  4  5  6  7 So, each AP will have 25 clients. Minimum 4 APs are sufficient.QUESTION 75An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used to ensure a consistent experience for all of the wireless clients?  the client that has the highest RF properties  the client that is used most by the company  the client that is used least by the company  the client with the worst RF characteristics Section: Wireless Site SurveyQUESTION 76An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used to ensure a consistent experience for all of the wireless clients?  the client that has the highest RF properties  the client that is used most by the company  the client that is used least by the company  the client with the worst RF characteristics Explanationhttps://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/Conducting_Site_Surveys_with_MR_AQUESTION 77Which statement about creating a mobility group is true, excluding mobility anchors?  Each WLC must use the same mobility name and be defined as a peer in each other’s static mobility members list.  If WLCs with HA SSO are deployed, each WLC in the WLC HA pair considered separately as a mobility peer.  The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.  A mobility groups does not require all WLCs in the group to use the same virtual IP address. QUESTION 78Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?  UDP 16666 for control plane, EoIP (IP protocol 97) for data plane  UDP 16668 for control plane, UDP 16667 for data plane  UDP 16667 for control plane, UDP 16666 for data plane  UDP 16666 for control plane, UDP 16667 for data plane QUESTION 79An engineer must ensure that the new wireless LAN deployment can support seamless roaming between access points using a standard based on an amendment to the 802.11 protocol. Which protocol must the engineer selects?  802.11i  802.11ac  802.11r  802.11e QUESTION 80A network engineer is working on a predictive WLAN design, the new wireless network must support access to Internet, email, voice, and the inventory database, to successfully support these services, which configuration must the engineer use for the signal strength levels and SNR on the planning tool?  signal strength of -67 dBm, 25-dB SNR, and maximum 1 percent packet loss.  signal strength of -67 dBm, 20-dB SNR, and maximum 5 percent, packet loss.  signal strength of 67 dBm, 20-dB SNR, and maximum 1 percent packet loss.  signal strength of-70 dBm,30-dB SNR. and maximum 10 percent packet loss. Explanationhttps://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057site-survey-guQUESTION 81An engineer is designing a network deployment for a college with six buildings Each building must have a WLC located in the IDF to support the APs. The wireless clients should be able to roam between the APs and the controllers. Which type of wireless architecture should be used?  Distributed  Centralized  Cloud  Autonomous Cloud-based architecture has controllers in the cloud, not on premises. Autonomous architecture means each AP is autonomous and is not managed by a WLC, distributed architecture is another term for autonomous architecture, so the same applies. Centralized architecture, a.k.a. split-MAC architecture is when all APs are managed centrally by WLCs, they do not need to be co-located. Understanding Cisco Wireless Architectures – CCNA Wireless 200-355 Official Cert Guide (2016) (apprize.best)https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob41dg/emob41dg-wrapper/ch2_Arch.htmlQUESTION 82An engineer must ensure that the new wireless LAN deployment can support seamless roaming between access points using a standard based on an amendment to the 802.11 protocol. Which protocol must the engineer selects?  802.11i  802.11ac  802.11r  802.11e QUESTION 83Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?  UDP 16666 for control plane, EoIP (IP protocol 97) for data plane  UDP 16668 for control plane, UDP 16667 for data plane  UDP 16667 for control plane, UDP 16666 for data plane  UDP 16666 for control plane, UDP 16667 for data plane QUESTION 84An enterprise has moved most services to the cloud, including email applications and real-time communication. Which feature must be enabled on the wireless network to improve the user experience?  QoS  Radio management  Interference mitigation  Fast secure roaming Explanationhttps://community.cisco.com/t5/wireless-mobility-documents/what-is-cckm-and-how-does-it-affect-fast-anQUESTION 85An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. What is the minimum requirement for the design?  overlapping -72 dBm coverage from two access points  continuous -67 dBm coverage from one access point  continuous -72 dBm coverage from one access point  overlapping -67 dBm coverage from two access points So -67dBm covers both Data & Voice with a single APQUESTION 86A customer is looking for a network design with Cisco Hyperlocation using AP4800 for location tracking via a custom mobile app issues appeared in me past with refresh rates for location updates What needs to be implemented to meet these requirements?  Cisco FastLocate technology  redundant CMX and fetch location in round-robin fashion  device Bluetooth via the app  Cisco CMX SDK in the location app https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-8/b_ap_4800_hyperlocation_deployment_guide.htmlQUESTION 87A customer is concerned about mesh backhaul link security. Which level of ecnryption does the backhaul link use?  hash  AES  WEP  3DES QUESTION 88What causes the most signal attenuation, based on the wireless design tools?  cinder block wall  metal door  glass wall  office window Section: Wireless Site SurveyQUESTION 89A customer is concerned about mesh backhaul link security. Which level of encryption does the backhaul link use?  hash  AES  WEP  3DES Section: Wireless Site SurveyQUESTION 90An engineer is reducing the subnet size of the corporate WLAN by segmenting the VLAN into smaller subnets.Clients will be assigned a subnet by location. Which type of groups can the engineer use to map the smaller subnets to the corporate WLAN?  WLC port groups  RF groups  AP groups  interface groups  Loading … 300-425 Dumps for success in Actual Exam: https://www.examslabs.com/Cisco/CCNP-Enterprise/best-300-425-exam-dumps.html --------------------------------------------------- Images: https://blog.examslabs.com/wp-content/plugins/watu/loading.gif https://blog.examslabs.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2022-12-20 16:11:13 Post date GMT: 2022-12-20 16:11:13 Post modified date: 2022-12-20 16:11:13 Post modified date GMT: 2022-12-20 16:11:13