[May-2023] 200-301 Free Sample Questions to Practice One Year Update [Q488-Q505] : Exams Labs Braindumps : http://blog.examslabs.com

QUESTION 488
What is a function of Wireless LAN Controller?

register with a single access point that controls traffic between wired and wireless endpoints.

use SSIDs to distinguish between wireless clients.

send LWAPP packets to access points.

monitor activity on wireless and wired LANs

QUESTION 489
DRAG DROP

QUESTION 490
What must a network administrator consider when deciding whether to configure a new wireless network with APs in autonomous mode or APs running in cloud- based mode?

Autonomous mode APs are less dependent on an underlay but more complex to maintain than APs in cloud-based mode.

Cloud-based mode APs relay on underlays and are more complex to maintain than APs in autonomous mode.

Cloud-based mode APs are easy to deploy but harder to automate than APs in autonomous mode.

Autonomous mode APs are easy to deploy and automate than APs in cloud-based mode.

QUESTION 491
Refer to the exhibit.

An engineer is configuring an EtherChannel using LACP between Switches 1 and 2 Which configuration must be applied so that only Switch 1 sends LACP initiation packets?

Switch 1 (config-if)#channel-group 1 mode on
Swrtch2(config-if)#channel-group 1 mode passive

Switch1(config-if)#channel-group 1 mode passive
Switch2(config-if)#channel-group 1 mode active

Switch1{config-if)#channel-group 1 mode active
Switch2(config-if)#channel-group 1 mode passive

Switch1(config-if)#channel-group 1 mode on
Switch2(config-if)#channel-group 1 mode active

QUESTION 492
A client experiences slow throughput from a server that is directly connected to the core switch in a data center. A network engineer finds minimal latency on connections to the server, but data transfers are unreliable, and the output of the show interfaces counters errors command shows a high FCS-Err count on the interface that is connected to the server.
What is the cause of the throughput issue?

a physical cable fault

a speed mismatch

high bandwidth usage

a cable that is too long

QUESTION 493
Drag and Drop Question
Drag each route source from the left to the numbers on the right. Beginning with the lowest and ending with the highest administrative distance.

QUESTION 494
The OSPF Hello protocol performs which of the following tasks? (Choose two.)

It negotiates correctness parameters between neighboring interfaces.

It broadcasts hello packets throughout the internetwork to discover all routers that are running OSP

It provides dynamic neighbor discovery.

It detects unreachable neighbors in 90 second intervals.

It uses timers to elect the router with the fastest links as the designated router.

It maintains neighbor relationships.

QUESTION 495

Refer to the exhibit. How does SW2 interact with other switches in this VTP domain?

It transmits and processes VTP updates from any VTP clients on the network on its trunk ports.

It processes VTP updates from any VTP clients on the network on its access ports.

It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports.

It forwards only the VTP advertisements that it receives on its trunk ports.

QUESTION 496
Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.

QUESTION 497
Refer to the exhibit.

Which route does R1 select for traffic that is destined to 192 168.16.2?

192.168.16.0/21

192.168.16.0/24

192.168 26.0/26

192.168.16.0/27

QUESTION 498
What is the purpose of an SSID?

It provides network security

It differentiates traffic entering access posits

It identities an individual access point on a WLAN

It identifies a WLAN

QUESTION 499
How does HSRP provide first hop redundancy?

It load-balances traffic by assigning the same metric value to more than one route to the same destination in the IP routing table.

It load-balances Layer 2 traffic along the path by flooding traffic out all interfaces configured with the same VLAN.

It forwards multiple packets to the same destination over different routed links in the data path

It uses a shared virtual MAC and a virtual IP address to a group of routers that serve as the default gateway for hosts on a LAN

QUESTION 500
What criteria is used first during the root port selection process?

local port ID

lowest path cost to the toot bridge

lowest neighbor’s bridge ID

lowest neighbor’s port ID

QUESTION 501
Refer to the exhibit.

The show ip ospf interface command has been executed on R1 How is OSPF configured?

The interface is not participating in OSPF

A point-to-point network type is configured

The default Hello and Dead timers are in use

There are six OSPF neighbors on this interface

QUESTION 502
R1 as an NTP server must have:
* NTP authentication enabled
* NTP packets sourced from Interface loopback 0
* NTP stratum 2
* NTP packets only permitted to client IP 209.165 200 225
How should R1 be configured?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

QUESTION 503
R1 has learned route 10.10.10.0/24 via numerous routing protocols.
Which route is installed?

route with the next hop that has the highest IP

route with the lowest cost

route with the lowest administrative distance

route with the shortest prefix length

QUESTION 504
Refer to the exhibit.

How does router R1 handle traffic to 192.168.10.16?

It selects the IS-IS route because it has the shortest prefix inclusive of the destination address.

It selects the EIGRP route because it has the lowest administrative distance.

It selects the OSPF route because it has the lowest cost.

It selects the RIP route because it has the longest prefix inclusive of the destination address.

QUESTION 505
Which set of actions satisfy the requirement for multifactor authentication?

The user enters a user name and password, and then re-enters the credentials on a second screen.

The user swipes a key fob, then clicks through an email link.

The users enters a user name and password, and then clicks a notification in an authentication app on a mobile device.

The user enters a PIN into an RSA token, and then enters the displayed RSA key on a login screen.