Pass Cisco 300-510 Exam With Practice Test Questions Dumps Bundle [Q35-Q50]

June 18, 2023 300-510, Cisco 0 Comments

Pass Cisco 300-510 Exam With Practice Test Questions Dumps Bundle [Q35-Q50]

Rate this post

Pass Cisco 300-510 Exam With Practice Test Questions Dumps Bundle

2023 Valid 300-510 test answers & Cisco Exam PDF

The exam requires a deep understanding of various routing protocols, such as OSPF, BGP, and IS-IS, and their implementation in a service provider network. Candidates should also be familiar with MPLS VPN technologies, as well as network automation and programmability. The exam is designed to test the candidate’s ability to configure, troubleshoot, and optimize the routing solutions in a service provider network.

QUESTION 35
Refer to the exhibit. When implementing SRv6, which SID does R2 propagate into area 0 for the prefix 2001:DB8:1:1/128?

120

230

110

QUESTION 36
After changing the IP address on an IOS XR router, an engineer cannot ping the new address Which step did the engineer forget to complete?

commit the configuration

roll back the configuration

save the running configuration

merge the configuration

QUESTION 37
Refer to the exhibit.

After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Router 2 receives a Type 5 LSAs from router 1 for its connected subnets

Router 2 uses router 3 as the next hop for 192.168.0.0/24

Router 2 uses router 1 as the next hop for 192.168.0.0/24

Router 2 receives a Type 7 LSAs from router 3 for its connected subnets

QUESTION 38
You have configured MSDP peering between two autonomous systems that pass traffic between two sites, but the peering has failed to come up.
Which task do you perform to begin troubleshooting the problem?

Verify that multicast has been disabled globally

Verify that PIM-DM is configured on the source interface

Verify that both source interfaces are reachable from both peers

Verify that the two MSDP peers allow asymmetric routing

QUESTION 39
Which cost is the default when redistributing routes from BGP to OSPF?

infinite

automatic

Reference:
http://www.ciscopress.com/articles/article.asp?p=27573

QUESTION 40
Refer to the exhibit.

Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)

The two routers are in the same area

The two routers are in different subnets

The two routers have password mismatch issues

The two routers have the same network ID

The two routers are in different areas

QUESTION 41
What is used by SR-TE to steer traffic through the network?

shortest path calculated by IGP

dynamic rules

path policy

explicit maps

Reference:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/segment-routing/configuration/guide/b-seg-routing-cg-asr9k/b-seg-routing-cg-asr9k_chapter_0100.html

QUESTION 42
Refer to the exhibit. An administrator is troubleshooting Internet access issues on a customer’s network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them. Which action should be taken to correct the problem?

Associate the default route with a VRF

Add the default-information originate command to the configuration

Configure the default route under any routing protocol other than IS-IS

Configure R1 as a Layer 1 router

QUESTION 43
Refer to the exhibit.

An engineer is addressing an IS-IS design issue which is running within the topology. All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet. Which statement about the design is true?

R4 prefer to reach R5 using R1 as the next hop

All links have equal cost if the default metric is used

R5 prefers to use R4 as the next hop for all routes

R1 prefer to use R5 as the next hop to reach R4

QUESTION 44

Refer to the exhibit. After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Router 2 receives a Type 5 LSAs from router 1 for its connected subnets

Router 2 uses router 3 as the next hop for 192.168.0.0/24

Router 2 uses router 1 as the next hop for 192.168.0.0/24

Router 2 receives a Type 7 LSAs from router 3 for its connected subnets

QUESTION 45
Refer to the exhibit. Which two commands must the engineer configure for the company’s PIM- PIM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface without affecting normal operation? (Choose two)

enable auto-rp listener

enable sparse-dense mode

enable sparse-mode

enable Auto-RP announcements

enable dense mode

QUESTION 46
Refer to the exhibit.

An engineer is troubleshooting IS-IS configuration between two areas. IS-IS Area-A network 30.1.1.0/24 is leaked into IS-IS Area-B. R2 is failing to filter the route updates from network 10.1.1.0/24. Which configuration must the engineer apply to resolve the issue?

R2(config)# ip prefix-list List2 seq 5 deny 10.1.1.0/24
R2(config)# interface fastethernet 0/0
R2(config-if)# ip router isis 100
R2(config-if)# router isis 100
R2(config-router)# distribute-list gateway List2 in

R2(config)# ip prefix-list List1 seq 3 deny 10.1.1.0/24
R2(config)# ip prefix-list List1 seq 5 permit 30.1.1.0/24 ge 25 1e
R2(config)# ip prefix-list List1 seq 10 permit 0.0.0.0/le 32
R2(config)# interface fastethernet 0/0
R2(config-if)# ip router isis 122
R2(config-if)# router isis 122
R2(config-router)# distribute-list prefix List1 in

R1(config)# ip prefix-list List2 seq 5 deny 10.1.1.0/24
R1(config)# interface fastethernet 0/0
R1(config-if)# ip router isis 100
R1(config-if)# router isis 100
R1(config-router)# distribute-list gateway List2 in
R (config-if)# router isis 150
R1(config-router)# distribute-list route-map Map1 in

R2(config)# access-list 101 deny ip any 10.1.1.0 0.0.0.127
R2(config)# access-list 101 permit ip any 30.1.1.0 0.0.0.63
R2(config)# access-list 101 deny ip any 0.0.0.0 0.0.0.0
R2(config)# interface fastethernet 0/0
R2(config-if)# ip router isis 121
R2(config-if)# router isis 121
R2(config-router)# distribute-list 101 in

QUESTION 47
Refer to the exhibit.

Refer to the exhibit. A network engineer just replaced five routers on this OSPF network. When the routing protocol is brought up, R5 cannot reach routes that originate on R1. The engineer verified that all connected links have established neighbor relationships. R5 reaches routes originating on R3 and R4. Which action resolves the issue?