NO.51 What is required when implementing captive portal an AOS-CX switches?

NO.52 An administrator has an aggregation layer of 8325CX switches configured as a VSX pair. The administrator is concernedthat when OSPF network changes occur, the aggregation switches will respond to the changes slowly, and this will affectnetwork connectivity especially VoIP calls, in the connected access layer switches What should the administrator do on the aggregation layer switches to alleviate this issue?

NO.53 Examine the commands entered on an AOS-CX switch:

What is true regarding this configuration for traffic received on interface 100?

NO.54 An administrator of a company has concerns about upgrading the access layer switches The users rely heavily on wireless and VoIP telephony Which is the best recommendation to ensure a short downtime for the users during upgrading the access layer switches?

NO.55 Examine the configuration of Core-1 and Core-2. AOS-CX switches configured as a VSX stack:
Core1: Interlace lag 256
no shutdown
no routing
vlan trunk allowed all
lacp mode active Interface 1/1/46
no shutdown
lag 256 Interface 1/1/47
no shutdown
lag 256
VSX
Inter-switch-link lag 256
vsx-sync vsx-global
exit
Cofe2: interlace lag 250
no shutdown
no routing
vlan trunk allowed all
lacp mode active
Interlace 1/1/46
no shutdown
lag 256 Interface 1/1/47
no shutdown
lag 256 vsx
inter-switch-link lag 256
exit
When using the “show vsx status” command, the two switches fall to connect and successfully synchronize. What should the administrator do to fix this issue?

NO.56 A company has a third-party AAA server solution. The campus access layer was just upgraded to AOS-CX switches that perform access control with MAC-Auth and 802.1X. The company has an Aruba Mobility Controller (MC) solution for wireless, and they want to leverage the firewall policies on the controllers for the wired traffic.
What is correct about how the company should implement a security solution where the wired traffic is processed by the MCs?

NO.57 Examine the following AOS-CX configuration:

Based on this configuration, which statement is correct regarding IoT traffic?

NO.58 Which AOS-CX switches support weighted fair queuing (WFQ)?

NO.59 A customer has twenty AOS-CX switches that will be managed by NetEdit and would like support for NetEdit these switches will exist in the network for at least five years.
Which type of licensing should be used by this customer?

NO.60 How is NetEdit installed at a customer location?

NO.61 An administrator has an aggregation layer of 8325CX switches configured as a VSX pair. The administrator is concerned that when OSPF network changes occur, the aggregation switches will respond to the changes slowly, and this will affect network connectivity, especially VoIP calls, in the connected access layer switches.
What should the administrator do on the aggregation layer switches to alleviate this issue?D18912E1457D5D1DDCBD40AB3BF70D5D

NO.62 Examine the network topology.

The network is configured for OSPF with the following attributes:
Here is the OSPF configuration performed on Core1:

Based on the above information, what is correct?

NO.63 An administrator wants to use an existing Aruba gateway’s firewall policies to filter both wireless and wired traffic. Which AOS-CX switch feature should a customer implement to ensure the gateway applies the same or similar firewall policies to users’ wired and wireless traffic?

NO.64 An AOS-CX switch is configured to implement downloadable user roles. Examine the AOS-CX switch output:

Based on this output, what is the state of the user’s access?

NO.65 An administrator is designing an access layer solution in a data center. A key requirement is to dual-home mission-critical server connections to two different switches, ensuring that the servers always have network access, even during switch software upgrades. This feature should support strictly-controlled provisioning.
What would best meet the administrator’s needs when deploying AOS-CX switches?

NO.66 Examine the attached exhibit.

The network administrators is trying to add a remote location as area 3 to the network shown in the diagram.
Based on current connection restrictions, the administrator cannot connect area 3 directly to area 0. The network is using AOS-CX switches.
Which feature should the administrator implement to provide connectivity to the remote location?