[Jul-2022] Network Appliance NS0-183 DUMPS WITH REAL EXAM QUESTIONS [Q28-Q47]

July 7, 2022 NS0-183, Network Appliance 0 Comments

[Jul-2022] Network Appliance NS0-183 DUMPS WITH REAL EXAM QUESTIONS [Q28-Q47]

Rate this post

[Jul-2022] Network Appliance NS0-183 DUMPS WITH REAL EXAM QUESTIONS

2022 New ExamsLabs NS0-183 PDF Recently Updated Questions

NetApp NS0-183 Exam Certification Details:

Number of Questions	60
Sample Questions	NetApp NS0-183 Sample Questions
Exam Registration	PEARSON VUE
Exam Name	Storage Installation Engineer ONTAP
Passing Score	67%
Recommended Training	ONTAP Clustered Installation Workshop (ILT) ONTAP Cluster Administration (vILT/ILT) Universal FAS Installation (WBT) Introduction to NetApp Installation Standard (WBT)
Duration	90 minutes

NEW QUESTION 28
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)

Remove cables connected to the controller until you find the one responsible for the controller issue.

Review AutoSupport messages which could explain the controller state.

Execute Config Advisor again to check for new errors.

Let the customer know the cluster is operating normally while the amber LED is on.

NEW QUESTION 29
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?

System Diagnostics

Cloud Insights

Active IQ Config Advisor

Active IQ Unified Manager

NEW QUESTION 30
You were asked to install a FAS9000 with two quad-port SAS PCI cards. The SAS PCI cards are installed in slot 9 and slot 1. In preparation for the installation, you are filling out the SAS cabling worksheet. In this scenario, which ports are used for the second stack?

9a/1d

9c/1a

9b/1b

9a/1a

NEW QUESTION 31
You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?

Active IQ Config Advisor

Interoperability Matrix Tool (IMT)

Hardware Universe (HWU)

mysupport.netapp.com site

NEW QUESTION 32
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?

routing

BGP

broadcast domains

IPspaces

NEW QUESTION 33
You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.
Which tool would you use to accomplish this task?

Active IQ scheduled reports

NetAppDocs output report

ONTAP System Manager

Active IQ Config Advisor worksheet

NEW QUESTION 34
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.

Referring to the exhibit, which steps are required to get an HA cabled system?

1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.

1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.

1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.

1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.

NEW QUESTION 35
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.

Referring to the exhibit, which steps are required to get an HA cabled system?

1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.

1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.

NEW QUESTION 36
Click the Exhibit button.

You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.
Referring to the exhibit, what must you do to solve this problem?

Configure more than one IPspace.

Configure the MTU consistently across the cluster.

Configure the correct Ethernet ports in all broadcast domains.

Configure the LIFs using separate home nodes.

NEW QUESTION 37
Which statement regarding Epsilon is true?

Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.

The node holding the epsilon has extra fractional vote weight.

Whenever a new node is added, the epsilon is automatically reassigned to this node.

The epsilon acts as a tiebreaker in a 2-node cluster.

NEW QUESTION 38
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)

Active IQ Config Advisor

Interoperability Matrix Tool

Active IQ System Manager

Hardware Universe

NEW QUESTION 39
What is the maximum number of data disks that a RAID-TEC RAID group has?

NEW QUESTION 40
You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer’s site, you notice that there are multiple breakout cables and four Cisco 3232C switches. In this scenario, which statement is true?

A 4-node AFF A300 cluster requires four Cisco 3232C switches.

Cisco best practices require four Cisco 3232C switches for high availability.

A 4-node AFF A300 cluster requires two Cisco 3232C switches for the cluster interconnect and two for management.

Your customer ordered a MetroCluster IP configuration.

NEW QUESTION 41
One of the nodes in your ONTAP 9.7 cluster has failed and is not coming back online.
Which two methods would you use to connect to the node failing to come back online? (Choose two.)

Use the Intelligent Platform Management Interface.

Use the Service Processor Interface.

Use Secure Shell.

Use Telnet.

NEW QUESTION 42
Which three components are required when setting up a new ONTAP cluster? (Choose three.)

password

cluster management IP

node management IP

Advanced Drive Partitioning

intercluster IP

NEW QUESTION 43
What are two ways to identify an AFF All SAN Array system? (Choose two.)

View the ONTAP System Manager system nodes.

View the ONTAP System Manager cluster settings.

Use the cluster image show CLI command.

Use the san config show CLI command.

Ways to identify an ASA system You can identify an ASA system using ONTAP System Manager or using the ONTAP command line interface (CLI). From the ONTAP System Manager dashboard, you can click on the system nodes. The personality type is displayed as “ASA” for ASA systems. From the CLI, you can use san config show command. The ASA value returns as true for ASA systems
https://docs.netapp.com/us-en/ontap/task_asa_software_configuration.html#asa-host-settings-and-utilities

NEW QUESTION 44
Which hot-swappable transceiver is required to obtain full performance from a Cisco Nexus 3232C cluster-interconnect switch?

QSFP28

QSFP+

SFP+

SFP

NEW QUESTION 45
You just installed two nodes into an existing ONTAP cluster.

When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.
Referring to the exhibit, which statement is true?

The node-management LIF has to be on e0M for NTP to work.

The DNS is not configured for this node.

The NTP is adjusting in small increments.

No NTP server is configured for this node.

NEW QUESTION 46
You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.
In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)

term-based

perpetual

base

master

Explanation/Reference: https://www.netapp.com/pdf.html?item=/media/17239-tr4598pdf.pdf (10)

NEW QUESTION 47
You want to create a new intercluster LIF for cross-cluster replication and use the CLI. After you create the nac101_intercluster_lif_icl LIF, you are not able to see the LIF in the list of local intercluster LIFs.

Referring to the exhibit, what is the problem?

The assigned port for the intercluster e1c LIF is in the down admin state.

The intercluster LIF has assigned an IP address that is not in the intercluster VLAN.

The LIF that was created has the wrong role type.

The home node of the new intercluster LIF has reached the maximum of four intercluster LIFs.

Loading …

Network Appliance NS0-183 Exam Syllabus Topics:

Topic	Details
Topic 1	Demonstrate knowledge of the purpose of the management network Identify the functions of supported switches
Topic 2	Describe how to use NetApp configurations Describe how to complete the service report
Topic 3	Demonstrate knowledge of how a node should be added or replaced Describe basic equipment installation steps
Topic 4	Demonstrate knowledge of handoff procedures to the customer Describe the cluster network, e.g., multi-node, single node clusters