FCSS_EFW_AD-7.4 Questions Prepare with Learning Information! 2025 Regularly updated [Q50-Q67] : Exams Labs Braindumps : http://blog.examslabs.com

NEUE FRAGE 50
When investigating FortiGuard connectivity issues, which action is a valid troubleshooting step?

Configure a virtual IP to forward port 443 to the FortiGate external IP.

Verify management VDOM internet access.

Use the FortiGuard real-time debug command to verify rating requests.

Verify that DNS requests are being proxied, if auto-update tunneling is enabled.

NEUE FRAGE 51
Examine the output of the ‘get router info bgp summary’ command shown in the exhibit; then answer the question below.

Which statements are true regarding the output in the exhibit? (Choose two.)

BGP state of the peer 10.125.0.60 is Established.

BGP peer 10.200.3.1 has never been down since the BGP counters were cleared.

Local BGP peer has not received an OpenConfirm from 10.200.3.1.

The local BGP peer has received a total of 3 BGP prefixes.

NEUE FRAGE 52
Refer to the exhibit, which contains the partial output of a diagnose command.

Based on the output, which two statements are correct? (Choose two.)

The remote gateway has quick mode selectors containing a destination subnet of 10.1.2.0/24.

The remote gateway IP is 10.200.5.1.

DPD is disabled.

Anti-replay is enabled.

NEUE FRAGE 53
Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

OSPF interface network types match.

OSPF router IDs are unique.

OSPF interface priority settings are unique.

Authentication settings match.

OSPF link costs match.

NEUE FRAGE 54
Which real time debug should an administrator enable to troubleshoot RADIUS authentication problems?

Diagnose debug application radius -1.

Diagnose debug application fnbamd -1.

Diagnose authd console -log enable.

Diagnose radius console -log enable.

NEUE FRAGE 55
Which two tasks are automated using the Import Configuration wizard on FortiManager? (Choose two.)

Importing firewall address objects from managed devices

Importing interface mappings from managed devices

Importing static and dynamic route configurations from managed devices

Importing devices to FortiManager

NEUE FRAGE 56
Which of the following conditions must be met for a static route to be active in the routing table?
(Wählen Sie drei aus.)

The next-hop IP address is up.

There is no other route, to the same destination, with a higher distance.

The link health monitor (if configured) is up.

The next-hop IP address belongs to one of the outgoing interface subnets.

The outgoing interface is up.

NEUE FRAGE 57
What does the dirty flag mean in a FortiGate session?

Traffic has been blocked by the antivirus inspection.

The next packet must be re-evaluated against the firewall policies.

The session must be removed from the former primary unit after an HA failover.

Traffic has been identified as from an application that is not allowed.

NEUE FRAGE 58
Examine the following partial output from a sniffer command; then answer the question below.

What is the meaning of the packets dropped counter at the end of the sniffer?

Number of packets that didn’t match the sniffer filter.

Number of total packets dropped by the FortiGate.

Number of packets that matched the sniffer filter and were dropped by the FortiGate.

Number of packets that matched the sniffer filter but could not be captured by the sniffer.

NEUE FRAGE 59
View the exhibit, then answer the question below.

Which of the following commands will bring up the tunnel?

diagnose vpn tunnel up 10.200.1.1

diagnose vpn tunnel H2S_0 up

diagnose vpn tunnel up H2S_0

diagnose vpn tunnel up H2S_0_0

NEUE FRAGE 60
Refer to the exhibit, which shows the output of a debug command.

Welche zwei Aussagen über die Ausgabe sind richtig? (Wählen Sie zwei.)

In the network connected to port 4, two OSPF routers are down.

Based on the network type of port 4, OSPF hello packets will be sent to 224.0.0.5.

Based on the network type of port 4, OSPF hello packets will be sent to 224.0.0.6.

There are a total of 5 OSPF routers attached to the Port4 network segment.

NEUE FRAGE 61
View the exhibit, which contains the output of a debug command, and then answer the question below:

What statement is correct about this FortiGate?

It is currently in system conserve mode because of high CPU usage.

It is currently in FD conserve mode,

It is currently in kernel conserve mode because of high memory usage

It is currently in system conserve mode because of high memory usage

NEUE FRAGE 62
Refer to the exhibit, which shows a session entry.

Which statement about this session is true?

It is an ICMP session from 10.1.10.10 to 10.200.5. 1.

It is a TCP session in close_wait state, from 10. l. 10.10 to 10.200.1.1.

It is an ICMP session from 10.1.10.10 to 10.200.1.1.

It is a TCP session in the established state, from 10.1.10.10 to 10.200.5.1.

NEUE FRAGE 63
Which two statements about FortiManager is true when it is deployed as a local FDS? (Choose two.)

It supports rating requests from both managed and unmanaged devices.

It caches available firmware updates for unmanaged devices.

It can be configured as an update server, or a rating server, but not both.

It provides VM license validation services.

NEUE FRAGE 64
Refer to the exhibit, which shows the output of a debug command.

What can be concluded from the debug command output?

The OSPF router with the ID 0.0.0.69 has its OSPF priority set to 0.

The local FortiGate has a different MTU value from the OSPF router with ID 0.0.0.2, based on the state information.

There are more than two OSPF routers on the wan2 network.

The interface ToRemote is a broadcast OSPF network.

NEUE FRAGE 65
Refer to the exhibit, which contains a CLI script configuration on FortiManager.

An administrator configured the CLI script on FortiManager, but the script failed to apply any changes to the managed device after being executed.
What are two reasons why the script did not make any changes to the managed device? (Choose two.)

Static routes can be added using only TCL scripts.

The commands that start with the # sign did not run.

CLI scripts must start with #!.

Incomplete commands can cause CLI scripts to fail.

NEUE FRAGE 66
Sehen Sie sich das folgende Exponat an:

Which two statements about the BGP peer are true? (Choose two.)

Since the BGP counters were last reset, the BGP peer 10.200.3.1 has never been down.

For the peer 10.125.0.60, the BGP state is Established.

The local BGP peer has not established a TCP session to the BGP peer 10.200.3.1.

The local BGP peer has received a total of three BGP prefixes.

NEUE FRAGE 67
An administrator added the following Ipsec VPN to a FortiGate configuration:
configvpn ipsec phasel -interface
edit “RemoteSite”
set type dynamic
set interface “portl”
set mode main
set psksecret ENC LCVkCiK2E2PhVUzZe
next
end
config vpn ipsec phase2-interface
edit “RemoteSite”
set phasel name “RemoteSite”
set proposal 3des-sha256
next
end
However, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection.
The output is shown in the exhibit.

What is causing the IPsec problem in the phase 1?

The incoming IPsec connection is matching the wrong VPN configuration

The phrase-1 mode must be changed to aggressive

The pre-shared key is wrong

NAT-T settings do not match

FCSS_EFW_AD-7.4 Fragen Bereiten Sie sich mit Lerninformationen vor! 2025 Regelmäßig aktualisiert [Q50-Q67]