2026 100% Free HPE7-A06 Daily Practice Exam With 128 Questions [Q59-Q75]

July 25, 2026 HPE7-A06, HP 0 Comments

2026 100% Free HPE7-A06 Daily Practice Exam With 128 Questions [Q59-Q75]

4/5 - (2 votes)

2026 100% Free HPE7-A06 Daily Practice Exam With 128 Questions

HPE7-A06 exam torrent HP study guide

HP HPE7-A06 Exam Syllabus Topics:

Section	Objectives
Topic 1: Campus Network Architecture	– Scalable enterprise network topology design – Hierarchical campus design (core, distribution, access layers) – Redundancy, high availability, and load balancing strategies
Topic 2: Multicast and Traffic Optimization	– PIM-SM/SSM concepts (high-level) – IGMP snooping and multicast control
Topic 3: Aruba AOS-CX Switching Technologies	– Spanning Tree (RSTP/MSTP) operations – VLANs, trunking, and link aggregation (LACP) – VSX, VSF, and MC-LAG architecture
Topic 4: Automation and Programmability	– REST API and HTTPS interface usage – NETCONF/YANG and Python-based automation (conceptual)
Topic 5: Routing and Multilayer Switching	– Inter-VLAN routing and L3 switching – OSPF fundamentals and advanced operations – BGP basics in campus environments
Topic 6: Security and Access Control	– 802.1X authentication and NAC integration (ClearPass) – Role-based access control and segmentation
Topic 7: Network Troubleshooting and Operations	– Performance optimization (MTU, QoS, congestion) – Switch diagnostics and CLI-based troubleshooting

Q59. Refer to the exhibits.

An engineer has applied the above configuration to R1 and R2, however, the router’s OSPF adjacency never progresses past the “EXSTART/DR” state.

Which configuration action on either router will allow R1 and R2 to progress past the
“EXTART/DR” state?

Change the IP address and mask applied to interface 1/1/1 to a valid mask supported by RFC
2328.

Ensure the OSPF process is not configured with passive-interface default.

Remove the L3 MTU configuration.

Change R1 and R2 to a network type of point-to-point.

Q60. The administrator pf a large company noticed that there are some problems with UCC sessions on a wired network. Some employees complain about dropped calls and poor quality. The administrator wants to monitor jitter on AOS-CX switches with IP SLA, but notices results spiking to 100%.
What should the administrator check first to correct monitoring to run as desired?

number of NAE agents

source IP and source port combination

memory and processor usage

CoPP settings

Q61. Which minimal configurations must be completed for MSTP to work correctly? (Choose two.)

MSTP region

bridge priority number

revision number

MSTP enabled interfaces

creating MSTP instances

Q62. The new CTO has set a standard of using a passphrase TACACS for the switch that is 64 characters long for advanced security. What is the issue with this policy?

The standard should be 128 characters long

Most organizations use simple words

This is not technically possible

The organization should not be using TACACS for security policy

Q63. A customer tasked you with creating a new design for the IDFs in a large office building. A junior member of your staff took all of the technical requirements and produced a design to meet those requirements. You were asked to review the portion of the design below:
CUSTOMER REQUIREMENTS:
preference for stackable switches

Each closet should contain a single virtual switch.

dual 10Gbps fiber uplinks from each closet

capacity for 500 edge ports in each closet; no additional capacity required

lowest-cost AOS-CX switch that meets all requirements

PROPOSED DESIGN:
nine (9) AOS-CX 6200M (R8Q69A: Class4 PoE 4SFP+ switch (R8Q68A) HPE Aruba

Networking 6200M 46G 4SFP+ switch) in each closet
switches configured in a VSF (Virtual Switching Framework) stack, with auto-stacking enabled

uplinks configured on the first and last members of the stack

Does the proposed solution meet the technical requirements?

No. The proposed design does not meet the capacity requirements.

Yes. The proposed design meets the customer’s requirements.

No. The proposed design does not meet the requirements for uplink connectivity.

No. The proposed design is not the lowest-cost AOS-CX switch for this project.

Q64. You see the output unknown the first time you in the command, but the next time you see the following information displayed.

What aresome things you could took at in the switch to troubleshootthe issue? (Select two.)

diag interface transceiver al

diag interface 1/VX transceiver all

diag cable-diagnostic 1/1/X

diag cable 1/1/X

diag 1/1/X transceiver all

Q65. Which EAP methods are supported when configuring the 802.1X supplicant feature on the AOS- CX switch? (Choose two.)

EAP-TLS

EAP-TTLS

EAP-MD5

EAP-PEAP

EAP-TEAP

Q66. Two CX 8325 switches are configured as a cluster using VSX for the core role and two CX
6300M in VSF for the aggregation role. When a major software upgrade is issued on the switches, what is the method to achieve a hitless upgrade with the core switches?

ISSU update-software initiates the upgrade first on the primary switch, followed by the secondary

ISSU update-software initiates the upgrade first on the secondary switch, followed by the primary

VSX update-software initiates software upgrade first on the secondary switch, followed by the primary

VSX update-software initiates software upgrade first on the primary switch, followed by the secondary

Q67. The user’s device is failing 802.1 Xwith EAP-TLS authentication. We know that theclient-side certificate is valid. What is the likely cause of this issue? (Select two.)

The user’s device is not configured to use the correct gateway.

There is a problem with the ACL applied to the switch port

There Is an EAP-type mismatch.

The user’s device is using the wrong MAC address

The NAD is not able to communicate with DNS servers.

Q68. An OSPF router has learned a path to an external network by both an E1 and E2 advertisement, both routes having the same path cost.
Which path will the router prefer?

Both routes will be suppressed until the path conflict has been resolved.

The router will use both paths equally my means of ECMP.

The router will prefer the E1 path.

The router will prefer the E2 path.

Q69. What is the best practice for using Dynamic Segmentation?

Use UBT to create isolated networks for specific types of devices.

Use Dynamic Segmentation only on devices that are connected to the network via Wi-Fi.

Use LUR to assign roles to devices based on their location and DUR to assign roles to devices based on their user identity.

Use a combination of role-based access and overlay technologies to create a layered security approach

Q70. Refer to the four numborod slops in the exhibit.

Which action is the fourthstep in applying a role-to-role ACL on thetraffic from mobile device M1 to roleH2?

Switch A1 determines the destination role based on destination MAC or destination IP and enforces role-to-role ACLs.

Gateway 1 forwards thetraffic over the sialic VXLAN tunnel to the edge switch; this packet carries the Group Policy ID corresponding to the role ofM1.

The AP forwards the packet from M1 to gateway 1.

The edge switch acts as the intermediate node and transfers the Group Policy ID over static VXLAN to dynamic VXLAN tunnel and forwards the packet to switch Al.

The question asks for the fourth step in applying a role-to-role ACL on traffic from a mobile device (M1) to a role (H2) in a network using Dynamic Segmentation with VXLAN. This follows question 17, which identified the first step as the AP forwarding the packet to the gateway.
* Analysis of Options:
* Option A:Correct. The fourth step involves the destination switch (Switch A1) determining the destination role (H2) based on the destination MAC or IP address and applying the role-to-role ACL to permit or deny the traffic.
* Option B:Describes an earlier step (likely second or third) where the gateway forwards traffic over a VXLAN tunnel.
* Option C:Describes the first step, as identified in question 17.
* Option D:Describes an intermediate step (likely third) where the edge switch transfers the Group Policy ID over VXLAN.
* Why Option A is Correct:In HPE Aruba Networking’s Dynamic Segmentation architecture, the traffic flow for role-based ACLs in a VXLAN environment follows these steps:
* The AP forwards the packet from M1 to the gateway (question 17).
* The gateway assigns the source role (M1’s role) and forwards the packet over a VXLAN tunnel with the Group Policy ID.
* The edge switch transfers the Group Policy ID to the destination switch (A1) via VXLAN.
* Switch A1 determines the destination role (H2) based on the destination MAC or IP address and enforces the role-to-role ACL, as defined in the Group-Based Policy (GBP).
The fourth step is critical for policy enforcement, ensuring that traffic complies with the security policies defined between the source and destination roles, providing secure network segmentation.
* Relevance to Certification Objectives:
* Security (10%):Designing and troubleshooting role-based security policies in customer networks.
* Switching (19%):Implementing Layer 2/3 interconnection technologies like VXLAN for policy enforcement.
* WLAN (9%):Troubleshooting wireless traffic flows in Dynamic Segmentation.
References:
HPE Aruba Networking AOS-10 Configuration Guide: Dynamic Segmentation and VXLAN, detailing role- based policy enforcement.
HPE7-A06Study Guide: Covers Group-Based Policy and Dynamic Segmentation workflows.
HPE Aruba Networking Technical Documentation: Tunneled Node and Role-Based ACLs.

Q71. Drag and Drop Question
Match the BGP connection states to the conditions that could have caused that state.

Q72. Refer to the exhibit which illustrates the current configuration of Router-1.

Clients of VLAN 10 require access to services hosted in the 10.1.100.0/24subnet. This ‘equites one 01 more routes to be added to Rculer-1 that do not currently exist.
Which script would install a route from 10.2.10.0/24 to 10.1.100.0/24 on Router-1? A return path is not required as part of this answer.

there is no solution as Core-1 is not part of VRF service

ip route 0.0.0.0/0 10.255.101.11 vrf service
ip route 10.1.100.0/24 1/1/1:10.255.101.11 vrf IoT-Medical

ip route 0.0.0.0/0 10.255.101.11 vrf service
ip route 10.1.100.0/24 1/1/1 vrf IoT-Medical

ip route 0.0.0.0/0 10.255.101.11 vrf service
ip route 10.255.101.0/24 1/1/1 vrf IoT-Medical
ip route 10.1.100.0/24 10.255.101.11 vrf IoT-Medical

Q73. A Python developer could not modify the VLAN database on an AOS-CX switch through the REST API.
Which settings should the developer check first? (Select two.)

HTTPS settings

SSH settings

SNMP settings

REST API settings

local-user settings

Q74. You are configuring an SSID thatisusing 802.IX as a security mechanism. Whatis the reason tor using WPA3- Ertorpnse (CCM-128) when deploying Wi-Fi 6 networks?

WPA3-Entorprise(CCM-128) is also called WPA3-Entorpnso 192-bit mode. lt is WPA3 only and enforces specific EAP certificate ciphers.

WPA3-Enterprise (CCM-128) is also called WPA3-Ente’prise Transition Mode. It will allow WPA2 clients to conned.

WPA3-Enterprise(CCM-128) is also called WPA3-Eniarpnse Compatibility Mode. It will allow WPA2 clients to connect.

WPA3-Enterprise(CCM-128) is also called WPA3-EnterpriseOnly Mode. There is no support tor WPA2 clients.

Q75. Match the customer requirement with the relevant commands.